Titanium Grade 2 Round Bars, Sheets and Plates: Sizes, Standards and Procurement Guide

Titanium Grade 2 Titanium Grade 2 is a commercially pure titanium grade widely considered for industrial applications requiring a combination of corrosion resistance, formability and useful mechanical strength. It is identified by UNS R50400 and is available in different product forms, including round bars, sheets and plates.

For procurement teams, selecting the correct Titanium Grade 2 material involves more than specifying the grade. Product form, dimensions, applicable standard, material condition, certification requirements and inspection details must all be clearly communicated.

Manan Steel & Metals supplies specialty metals and alloys. Buyers looking for Titanium Grade 2 can contact the team with their required grade, product form and dimensions for enquiry.

Titanium Grade 2 Product Forms

Titanium Grade 2 is used in several product forms. The appropriate form depends on the component design, manufacturing process and applicable material specification.

1. Titanium Grade 2 Round Bars

Titanium Grade 2 round bars are considered for machined components and industrial parts where a solid cylindrical starting material is required.

Common procurement applications include:

  • Machined industrial components
  • Fastener and fitting manufacturing
  • Pump and valve components
  • Chemical processing equipment
  • General engineering applications

When enquiring, specify the required diameter, length, quantity and material condition. Also confirm whether the requirement is for a hot-worked, cold-worked or machined surface, as applicable.

2. Titanium Grade 2 Sheets

Titanium Grade 2 sheets are used where a relatively thin flat product is required for fabrication or component manufacturing.

Potential applications include:

  • Fabricated chemical-processing components
  • Industrial covers and panels
  • Equipment linings
  • Formed parts
  • Corrosion-resistant fabricated assemblies

Buyers should mention thickness, width, length, quantity and any surface-finish requirements.

3. Titanium Grade 2 Plates

Titanium Grade 2 plates are considered for heavier flat sections and fabricated industrial components.

They may be specified for:

  • Chemical processing equipment
  • Industrial fabrication
  • Equipment components
  • Machined plates and structural parts
  • Corrosion-resistant engineering assemblies

Plate thickness, width, length, flatness requirements and intended fabrication process should be confirmed before ordering.

Titanium Grade 2 Sizes: What Buyers Should Specify

There is no single universal size range that applies to every supplier or product form. Available dimensions depend on the manufacturing route, applicable specification, material condition and supplier capability.

Use the following information when preparing a purchase enquiry:

Product formImportant dimensions and details
Round barDiameter, length and quantity
SheetThickness, width, length and quantity
PlateThickness, width, length and quantity

For all forms, buyers should also specify:

  • Grade: Titanium Grade 2
  • UNS designation: R50400
  • Applicable material standard
  • Required material condition
  • Surface-finish requirements
  • Inspection and documentation requirements
  • Delivery location and required quantity

Providing complete dimensions helps suppliers assess the requirement accurately and reduces clarification during quotation.

ASTM Standards for Titanium Grade 2

The applicable ASTM specification depends on the product form. Buyers should not assume that one standard covers every Titanium Grade 2 product.

Commonly referenced specifications include:

ASTM B348 / B348M

This specification covers titanium and titanium alloy bars and billets. It is relevant when enquiring about Titanium Grade 2 bar products, subject to the exact product and specification requirements.

ASTM B265

ASTM B265 covers titanium and titanium alloy strip, sheet and plate. It is an important reference when specifying flat Titanium Grade 2 products.

ASTM B338

ASTM B338 covers seamless and welded titanium and titanium alloy tubes for condensers and heat exchangers. It may be relevant when the requirement involves tubular products rather than bars, sheets or plates.

Always confirm the current specification edition, grade designation, product form and applicable supplementary requirements with the buyer and supplier.

Reference: ASTM International

Documents to Check Before Purchasing Titanium Grade 2

Material documentation is an important part of industrial procurement, particularly when titanium is being purchased for critical equipment or regulated applications.

Before finalising an order, buyers should clarify the following:

1. Mill Test Certificate

Request the applicable Mill Test Certificate (MTC) and check that the grade, heat or lot identification, chemical analysis and mechanical test results correspond to the ordered material and specification.

2. Chemical Composition

Confirm that the reported chemical composition meets the limits of the specified grade and standard. Do not rely only on a product label or verbal grade confirmation.

3. Mechanical Test Results

Where required by the purchase specification, check the reported tensile properties, yield strength and elongation against the applicable product-form requirements.

4. Heat Number and Traceability

Confirm that material identification and traceability are maintained as required by the purchase order. The heat or lot number on the material should correspond to the supporting documentation.

5. Dimensions and Surface Condition

Check the supplied dimensions, tolerances and surface condition against the purchase requirement. Additional inspection may be necessary depending on the application.

How to Calculate the Approximate Weight of Titanium Grade 2 Round Bars

For preliminary estimation, buyers can use the following approximate formula:

Round bar weight (kg) = 0.00354 × D² × L

Where:

  • D = Diameter in millimetres
  • L = Length in metres

This estimate uses a typical titanium density of approximately 4.51 g/cm³. Actual weight can vary with dimensional tolerances and material characteristics. Use the supplier’s confirmed weight for commercial calculations and dispatch documentation.

For additional reference, see the Manan Steel & Metals Round Bar Weight Chart.

Common Procurement Mistakes to Avoid

Buyers can reduce material-selection and ordering errors by avoiding these common mistakes:

  1. Specifying only “Titanium” without mentioning Grade 2 or UNS R50400.
  2. Not identifying whether the requirement is for round bars, sheets or plates.
  3. Providing incomplete dimensions or quantity details.
  4. Assuming that ASTM B348, B265 and B338 are interchangeable.
  5. Not checking the MTC and material traceability requirements.
  6. Overlooking surface finish, tolerances and material condition.
  7. Selecting a material without checking its suitability for the actual operating environment.

The correct specification should be established before the purchase order is released.

Frequently Asked Questions About Titanium Grade 2 Sizes and Standards

1. What is the UNS number of Titanium Grade 2?

Titanium Grade 2 is identified by UNS R50400.

2. Which ASTM standard applies to Titanium Grade 2 round bars?

ASTM B348/B348M is a commonly referenced specification for titanium and titanium alloy bars and billets. Confirm the exact grade, product requirements and current edition before ordering.

3. Which ASTM standard covers Titanium Grade 2 sheets and plates?

ASTM B265 covers titanium and titanium alloy strip, sheet and plate. Confirm that the ordered grade and product condition meet the required specification.

4. Are Titanium Grade 2 round bars available in different diameters?

Titanium Grade 2 round bars are specified in different diameters and lengths. Actual supply dimensions depend on supplier capability and material availability. Share your required dimensions for confirmation.

5. What documents should I request when purchasing Titanium Grade 2?

Depending on the purchase specification, buyers may request an MTC, chemical analysis, mechanical test results, heat or lot identification and other agreed inspection documents.

6. Is Titanium Grade 2 suitable for marine and chemical-processing applications?

It is used in selected marine and chemical-processing applications because of its corrosion resistance. However, suitability depends on the exact chemical environment, concentration, temperature, flow conditions and design.

Enquire About Titanium Grade 2 at Manan Steel & Metals

Looking for Titanium Grade 2 round bars, sheets or plates for an industrial requirement?

Manan Steel & Metals welcomes enquiries from manufacturers, engineering companies, fabricators, maintenance teams and industrial buyers.

Share the following details to help us understand your requirement:

  • Material: Titanium Grade 2 / UNS R50400
  • Product form: Round Bar, Sheet or Plate
  • Required dimensions
  • Quantity
  • Applicable ASTM standard
  • Required documentation
  • Delivery location

Contact Manan Steel & Metals

Website: https://manansteel.com/
Email: sales@manansteel.com
Phone: +91 98198 76962

For enquiries, visit our Contact Us page.

SEO DETAILS – FOR PUBLISHING

SEO Title: Titanium Grade 2 Sizes, Bars, Sheets & Plates Guide

Focus Keyword: Titanium Grade 2 sizes

Secondary Keywords:

  • Titanium Grade 2 round bar sizes
  • Titanium Grade 2 sheet
  • Titanium Grade 2 plate
  • UNS R50400
  • Titanium Grade 2 ASTM standard
  • Titanium Grade 2 supplier India
  • Titanium Grade 2 procurement
  • Titanium Grade 2 material certificate

URL Slug: titanium-grade-2-round-bars-sheets-plates-sizes-guide

Meta Description: Explore Titanium Grade 2 sizes, round bars, sheets, plates, ASTM standards and procurement checks for industrial buying requirements.

Suggested Featured Image Filename: titanium-grade-2-round-bars-sheets-plates.jpg

Featured Image Alt Text: Titanium Grade 2 round bars, sheets and plates supplied for industrial applications

Featured Image Caption: Titanium Grade 2 product forms – round bars, sheets and plates.

Internal Links to Include:

External Links Included:

Publishing Checklist

  • Keep exactly one H1 heading (the blog title).
  • Use the title as the only H1; all main sections should be H2 and subsections H3.
  • Set the focus keyword to “Titanium Grade 2 sizes”.
  • Add the focus keyword naturally in the SEO title, introduction, one relevant subheading and meta description.
  • Add the featured image with the suggested alt text.
  • Check that all internal and external links open correctly.
  • Ensure the final published URL is not already in use.
  • Confirm technical values and applicable standard editions against the actual material documentation before publication.