Monel 400 Chemical Composition
Monel 400 is a nickel-copper alloy known for its combination of strength, toughness and resistance to many corrosive environments. Identified by UNS N04400, it is used in marine engineering, chemical processing, oil and gas equipment, pumps, valves and specialised industrial components.
For engineers and industrial buyers sourcing Monel 400 round bar, understanding its chemical composition, mechanical properties and corrosion resistance is essential. These characteristics help determine whether the material is suitable for the intended operating environment and manufacturing requirements.
This guide covers the chemical composition, tensile strength, yield strength, hardness, physical properties and corrosion behaviour of Monel 400, along with important material-selection considerations.
Table of Contents
ToggleMonel 400, also known as Nickel Alloy 400 or UNS N04400, is a nickel-copper solid-solution alloy.
Unlike precipitation-hardening alloys, Monel 400 develops increased strength primarily through cold working. Its mechanical properties depend on the amount of cold work, product form, manufacturing process and supplied material condition.
Common designations include:
Monel 400 is available in several product forms, including round bars, rods, sheets, plates, pipes, tubes and wire.
For buyers sourcing round bar, the material designation and applicable product specification should be confirmed before ordering.
The chemical composition of Monel 400 is primarily based on nickel and copper. These elements contribute to the alloy’s characteristic mechanical behaviour and corrosion resistance.
The commonly specified composition limits are:
| Element | Composition |
|---|---|
| Nickel plus Cobalt | 63.0% minimum |
| Copper | 28.0–34.0% |
| Iron | 2.5% maximum |
| Manganese | 2.0% maximum |
| Silicon | 0.50% maximum |
| Carbon | 0.30% maximum |
| Sulphur | 0.024% maximum |
These are specification limits, not a guaranteed analysis for every heat. Actual chemical composition should be checked against the applicable material standard and Mill Test Certificate.
Nickel: Nickel is the principal element in Monel 400. It contributes to the alloy’s mechanical characteristics and resistance in several corrosive environments.
Copper: Copper is the second major constituent and contributes to the alloy’s performance in reducing environments and selected chemical applications.
Iron: Iron is present within the specified composition limit and forms part of the alloy’s overall chemistry.
Manganese and Silicon: These elements are controlled within specified limits as part of the alloy’s chemical composition.
Carbon and Sulphur: These elements are also controlled because chemical composition requirements form part of material quality and specification compliance.
Monel 400 offers a combination of tensile strength, yield strength, ductility and toughness. Its actual mechanical properties depend on product form and condition.
For round bar procurement, the distinction between annealed, hot-finished and cold-drawn material is particularly important.
Tensile strength is the maximum tensile stress a material withstands during a tensile test before fracture.
For Monel 400 rod and bar in the annealed condition, the Special Metals technical bulletin provides nominal room-temperature tensile strength values of approximately 517–620 MPa.
Yield strength indicates the stress at which permanent deformation begins under the specified test method.
For annealed Monel 400 rod and bar, the same technical bulletin gives a nominal 0.2% offset yield strength range of approximately 172–345 MPa.
Elongation measures the material’s ability to deform plastically before fracture.
The nominal elongation range reported for annealed rod and bar is approximately 35–60%, depending on the material and test conditions.
Hardness indicates resistance to local indentation and is influenced by the material condition and degree of cold working.
For annealed rod and bar, the technical bulletin reports nominal Brinell hardness values of approximately 110–149 HB.
Important: These are reference values from the manufacturer’s technical bulletin, not universal guaranteed minimums for every diameter or supply condition. Always use the applicable ASTM specification and the actual MTC for acceptance.
Physical properties help engineers assess material weight, stiffness and thermal behaviour during component design.
| Property | Reference value |
|---|---|
| Density | 8.80 g/cm³ |
| Density | 0.318 lb/in³ |
| Modulus of elasticity in tension | Approximately 179 GPa |
| Modulus of rigidity | Approximately 65.5 GPa |
| Poisson’s ratio | 0.32 |
| Melting range | Approximately 1300–1350°C |
| Thermal conductivity at around 21°C | Approximately 22 W/m·K |
These values are reference data. The applicable design conditions and material documentation should be considered when using them for engineering calculations.
Monel 400 has a density of approximately 8.80 g/cm³. This is useful when estimating the weight of round bars and calculating material requirements.
The actual weight of a supplied bar depends on its diameter, length and dimensional tolerances.
The modulus of elasticity describes the material’s resistance to elastic deformation under an applied load.
It is an important design consideration for shafts, structural components and precision-machined parts.
Thermal conductivity and expansion characteristics influence how the material responds to temperature changes.
These properties should be considered when designing components exposed to thermal cycling or elevated operating temperatures.
Corrosion resistance is one of the major reasons Monel 400 is selected for specialised industrial applications.
The alloy performs well in many reducing environments, selected chemical solutions, seawater and alkaline media. However, corrosion performance depends strongly on the chemical composition of the service environment and its operating conditions.
Monel 400 is widely used in marine applications because of its performance in flowing seawater.
It is considered for pump shafts, propeller shafts, marine fasteners, fittings and other seawater-related equipment.
However, stagnant seawater and deposits can create conditions that encourage crevice or pitting corrosion. Flow conditions, fouling and component design must therefore be evaluated.
Monel 400 has particularly strong resistance to hydrofluoric acid under suitable conditions, including concentrations up to the boiling point as described in the Special Metals technical bulletin.
This makes it relevant to certain chemical-processing applications.
The actual concentration, temperature, aeration and process conditions must still be reviewed before material selection.
The alloy offers resistance to many hydrochloric acid environments under reducing conditions.
Its suitability depends on acid concentration, temperature and the presence of oxidising contaminants.
Monel 400 can perform in selected sulphuric acid environments, particularly under reducing conditions.
It should not be selected without checking the exact concentration, temperature and operating environment.
The alloy is used in selected alkaline and salt-containing environments where its corrosion characteristics are suitable.
Monel 400 has good resistance to chloride-induced stress corrosion cracking in many typical environments. However, no material should be assumed immune to every form of corrosion or every combination of stress and chemical exposure.
Although Monel 400 offers corrosion resistance in many environments, it is not universally suitable.
Special attention is required in:
For example, oxidising impurities such as ferric salts, nitrates and other oxidising compounds can increase corrosion attack in environments that would otherwise be relatively mild.
Material selection should therefore be based on the actual process chemistry rather than the general label of corrosion resistance.
The combination of nickel-copper chemistry, strength and corrosion resistance makes Monel 400 useful in selected industrial applications.
Potential uses include:
Selected applications include:
Potential applications include:
Material suitability must be confirmed against the actual service conditions and relevant engineering requirements.
Monel 400 is a solid-solution alloy that is strengthened through cold working.
Cold working involves plastic deformation below the recrystallisation temperature. It increases strength and hardness, but generally reduces ductility.
This means that two Monel 400 round bars may have different mechanical properties depending on their manufacturing route and supplied condition.
For example:
Annealed material: Generally offers greater ductility and lower strength compared with heavily cold-worked material.
Cold-drawn material: Can offer increased strength and hardness, depending on the degree of cold work and any subsequent treatment.
Hot-finished material: Has mechanical properties associated with its manufacturing process and final condition.
Buyers should specify the required material condition rather than assuming all Monel 400 bars have identical properties.
When purchasing Monel 400 round bars, buyers should check the technical details that directly affect material suitability.
Confirm the designation as Monel 400 / UNS N04400.
ASTM B164 is commonly specified for Monel 400 rod, bar and wire. Confirm the current edition and required product condition.
Check the chemical analysis against the applicable specification and MTC.
Confirm the tensile strength, yield strength, elongation and hardness requirements for the specified product form and condition.
Specify the diameter, length and dimensional tolerances.
Mention whether annealed, hot-finished or another specified condition is required.
Confirm the requirement for an MTC, chemical analysis, mechanical testing and any additional inspection reports.
For related material specifications, consult the ASTM International standards catalogue and the Special Metals Monel Alloy 400 technical bulletin.
Manan Steel & Metals deals in specialty metals and alloys, including Monel grades, for industrial and engineering requirements.
Buyers sourcing Monel 400 round bars can share their required grade, dimensions, applicable specification and documentation requirements.
For a clear enquiry, mention:
Explore Manan Steel & Metals and the round bar product section.
For pricing and supply enquiries, visit the Manan Steel & Metals contact page.
Monel 400 contains at least 63% nickel plus cobalt and approximately 28–34% copper, with controlled limits for iron, manganese, silicon, carbon and sulphur.
The Special Metals technical bulletin reports nominal tensile strength of approximately 517–620 MPa for annealed rod and bar. Actual values depend on product condition, size and applicable specification.
The reference density of Monel 400 is approximately 8.80 g/cm³.
Monel 400 offers good corrosion resistance in flowing seawater. However, stagnant conditions, deposits and crevices can create a risk of localised corrosion.
It can be suitable in selected hydrochloric acid environments, particularly under reducing conditions. Concentration, temperature and oxidising contaminants must be evaluated.
Yes. Cold working increases strength and hardness while generally reducing ductility. The degree of cold work influences the final mechanical properties.
The UNS designation of Monel 400 is N04400.
ASTM B164 is commonly referenced for nickel-copper alloy rod, bar and wire, including UNS N04400. Confirm the exact requirements and current edition before ordering.
Monel 400 combines nickel-copper chemistry, useful mechanical strength, toughness and resistance to many corrosive environments. Its performance in seawater and selected reducing chemical environments makes it an important material for marine, chemical-processing and industrial engineering applications.
For buyers, the correct material condition, mechanical properties, chemical composition and corrosion requirements must be verified before procurement. Checking the applicable specification and Mill Test Certificate helps ensure that the supplied Monel 400 round bar matches the intended engineering requirement.
For Monel 400 round bar and specialty alloy enquiries, contact Manan Steel & Metals.
SEO Title: Monel 400 Properties: Composition, Strength and Corrosion
Focus Keyword: Monel 400 properties
Secondary Keywords:
URL Slug: monel-400-chemical-composition-mechanical-properties-corrosion
Meta Description: Explore Monel 400 chemical composition, mechanical properties, tensile strength, density and corrosion resistance for industrial applications.
Featured Image Filename: monel-400-chemical-composition-mechanical-properties.jpg
Featured Image Alt Text: Monel 400 nickel copper alloy round bar showing UNS N04400 material for industrial applications
Featured Image Caption: Monel 400 chemical composition, mechanical properties and corrosion resistance.